Created on:2023-11-24

Winter maintenance of various types of agricultural machinery matters needing attention

Winter maintenance of various types of agricultural machinery matters needing attention


1. Tractor

tractor is large, it should pay more attention to the maintenance of the tractor in the cold winter. Be sure to descale, clean, adjust and lubricate all parts of the tractor during the season. Technical indicators such as valve clearance, fuel injection pressure and fuel injection advance angle should be adjusted to the specified range. The clutch, brake and operating mechanism should be fully adjusted to ensure that the tractor is in good technical condition and lay a good foundation for safe winter. At the same time should pay attention to the following points:

It is strictly forbidden to use wrong methods such as ignition, dragging, sliding slope, open flame baking, adding water after the car is started, and adjusting the fuel injection pressure to start:

When the weather is cold, the tractor is not easy to start. If the above method is used, the clutch and gearbox gears may be damaged by impact; to start correctly, you can use low-temperature starting fluid and spray it into the air filter. The injection time and injection volume should be controlled before starting. After starting, rotate at medium speed, and start only when the water temperature reaches 40 ℃ or above, and work with load only when the water temperature reaches 60 ℃.

It is forbidden to start without cooling water:

must remember to add water for the first time can not add boiling water, so as not to be cracked due to sudden heat of the body. If the water tank is boiling or water needs to be added during the operation of the tractor, cold water cannot be added suddenly. At this time, the operation should be stopped. After the water temperature drops, clean drinking water should be added appropriately to prevent the cylinder head and cylinder liner from bursting.

Do not forget to put all the cooling water:

When the temperature is 4 ℃ and below, remember that when parking at night and parking for a long time, tractors without antifreeze should drain the cooling water in the engine. When discharging cooling water, wait until the water temperature drops below 60 ℃ before discharging water, otherwise, it is easy to cause damage to the body or cylinder head, etc. Not to mention leaving before the cooling water is discharged, be sure to check whether it is discharged to prevent the water valve from being blocked by impurities, and the remaining water expands abnormally at low temperature and freezes the body.

It is forbidden to use unqualified firewood and engine oil:

tractor depends on the local temperature: if the lowest temperature is 0 to -5 ℃, choose -10 diesel; if the lowest temperature is -10 to -15 ℃, choose -20 diesel; if the lowest temperature is not lower than -30 ℃, choose -35 diesel; if the lowest temperature is about -40 ℃, choose -50 diesel. Therefore, when choosing diesel oil, the freezing point should be 5~10 ℃ lower than the local temperature. The engine oil used in winter has a high viscosity, which brings difficulties to lubrication and starting, so it should be replaced with No. 8 diesel engine oil; the lubricating oil in the gearbox and rear axle should be replaced with No. 11 diesel engine oil or No. 20 gear oil.

driving habits are strictly prohibited:

do not pay attention to driving methods, illegal operation. For example, before the engine is turned off, the throttle is blown indiscriminately, thinking that some diesel can be stored in the cylinder to facilitate easy starting next time. In fact, doing so will only cause the diesel to not be completely burned in the cylinder and cause carbon deposits, and may flow into the oil pan along the cylinder wall to dilute the oil, which will not only be of no benefit to the next start, but also affect the lubrication performance of the oil. Others do not add diesel in time, and fill the tractor fuel tank with diesel before the winter flameout. Otherwise, the water vapor in the air in the empty tank will be liquefied and condensed into water droplets after being cooled by the tank wall, which will be mixed into the diesel oil, causing the engine to fail to work normally.

2. Plant Protection UAV

plant protection unmanned aerial vehicles and related ancillary products operate in fields with complex environment. External factors such as dust, liquid medicine, dew and sundries affect the performance of the products. Timely clean and maintain the equipment, clean and wipe, lubricate and apply oil, check and calibrate, replace wearing parts, etc. to ensure that the equipment is in the best condition and prolong the service life of the products.

cleaning appearance: the operating environment of flying anti-plant protection is complex, and a large amount of liquid medicine and dust will adhere to the appearance of the equipment. timely cleaning will prevent corrosion of components from affecting normal operation.

structure inspection: The machine body of the plant protection drone has strong vibration. Check the bolts, buckles, rivets and other connecting parts. If there is wear, damage, looseness, slippage, rust, etc., replace or apply oil in time.

wearing parts: pesticides are corrosive to varying degrees, and parts in contact with pesticides (pipes, adapters, nozzles, flow meters, level gauges, etc.) should be checked and replaced in time.

battery maintenance:

Do not charge and discharge in high/low temperature environment. Extreme temperatures will affect the performance and life of the battery. Before charging, check whether the used battery has been cooled. Do not charge and discharge in a cold garage, basement, direct sunlight or near a heat source.

Batteries should be stored in a cool environment. Long-term storage of the battery, can be placed in a sealed bag or sealed explosion-proof box is better, the recommended ambient temperature of 10 ~ 25C, and dry, non-corrosive gas.

plant protection UAV should keep the battery warm before taking off, and keep the battery in a warm environment, such as in the house, in the car, in the incubator, etc. To quickly install the battery when taking off and perform the flight mission. When flying at low temperatures, try to shorten the time to half of the normal temperature state to ensure safe flight.

The normal use and maintenance of the battery of the land plant protection drone is an important way to extend the service life of the drone. Therefore, when maintaining the battery, it is necessary to pay attention to the above matters to ensure that the battery of the plant protection drone is not damaged and can be used normally.

3. Combine harvester

The sundries at the connection of the harvester should be cleaned, lubricated or sealed with oil injection; if the paint peeling of the rust-prone parts leads to exposure, it is necessary to paint in time to prevent rust. If it is a rubber belt, it should be wiped and dried to prevent pests and mice from harming. The metal chain can be cleaned with kerosene or diesel oil, then soaked in engine oil for 15-40 minutes, or soaked overnight, taken out and aired until no oil drips, coated with softening oil, and then wrapped in kraft paper and placed in a dry and ventilated place to avoid mildew and deformation.

harvester. They are easily aged and deteriorated after being exposed to sunlight, and their elasticity is poor, which will affect their use in the coming year. In the storage of these products, with paraffin oil coated on the surface, and then placed in direct sunlight in a ventilated dry place. Plastic products and springs will be deformed due to long-term pressure or improper storage, so the spring should be relaxed, the conveyor belt and the like should be disassembled and stored separately.

In addition, some random utensils, especially special tools and various spare parts, need to be stored separately and put in place after use to avoid loss caused by misplacing.

4. Baler

After each use of the baler, it must be maintained, cleaned and maintained, otherwise it is likely to affect its life. After the baler and the power machine are equipped, drive to the harvested wheat field, check whether the power of the power machine is in good contact with the baler, then start, pick up, and bundle. After hearing the alarm, stop the car and increase the throttle to make the baler fast. After hearing the sound of the rope being cut, pull the rope slightly and lift the back cover of the baler to make the grass baler drop, the next grass picking can be carried out after the bale is discharged, so that the cycle continues until the work is completed, and then after use, it should be cleaned to clean up all impurities such as straw in the machine, otherwise it will malfunction after a long time, affecting normal use.

cleaning: The baler should be cleaned with high-pressure gas, and protective glasses should be worn during cleaning to avoid damage to the glasses. Secondly, it can also be cleaned by the high-speed and large-capacity wind generated by the fan. Remember not to clean the baler with water, because the residue left after cleaning will cause the body to rust when soaked in water.

lubrication: baler need to lubricate the place generally includes roller chain and wheel bearing two parts. Generally speaking, every 1000 bales need to be lubricated with oil to all chains, but it is easy to absorb dust, so you can choose to lubricate the chain regularly at the end of the season and during the idle period, so that the chain is not as easy to be contaminated as it is during operation. The wheel bearings need to be removed for cleaning and replacement every year. When lubricating the wheel bearings, the bearing adjustment bolts should be tightened, and the wheel should be rotated at the same time, and the rotation will stop when it encounters resistance.



维修保养

Created on:2023-11-24

Winter maintenance of various types of agricultural machinery matters needing attention

Winter maintenance of various types of agricultural machinery matters needing attention


1. Tractor

tractor is large, it should pay more attention to the maintenance of the tractor in the cold winter. Be sure to descale, clean, adjust and lubricate all parts of the tractor during the season. Technical indicators such as valve clearance, fuel injection pressure and fuel injection advance angle should be adjusted to the specified range. The clutch, brake and operating mechanism should be fully adjusted to ensure that the tractor is in good technical condition and lay a good foundation for safe winter. At the same time should pay attention to the following points:

It is strictly forbidden to use wrong methods such as ignition, dragging, sliding slope, open flame baking, adding water after the car is started, and adjusting the fuel injection pressure to start:

When the weather is cold, the tractor is not easy to start. If the above method is used, the clutch and gearbox gears may be damaged by impact; to start correctly, you can use low-temperature starting fluid and spray it into the air filter. The injection time and injection volume should be controlled before starting. After starting, rotate at medium speed, and start only when the water temperature reaches 40 ℃ or above, and work with load only when the water temperature reaches 60 ℃.

It is forbidden to start without cooling water:

must remember to add water for the first time can not add boiling water, so as not to be cracked due to sudden heat of the body. If the water tank is boiling or water needs to be added during the operation of the tractor, cold water cannot be added suddenly. At this time, the operation should be stopped. After the water temperature drops, clean drinking water should be added appropriately to prevent the cylinder head and cylinder liner from bursting.

Do not forget to put all the cooling water:

When the temperature is 4 ℃ and below, remember that when parking at night and parking for a long time, tractors without antifreeze should drain the cooling water in the engine. When discharging cooling water, wait until the water temperature drops below 60 ℃ before discharging water, otherwise, it is easy to cause damage to the body or cylinder head, etc. Not to mention leaving before the cooling water is discharged, be sure to check whether it is discharged to prevent the water valve from being blocked by impurities, and the remaining water expands abnormally at low temperature and freezes the body.

It is forbidden to use unqualified firewood and engine oil:

tractor depends on the local temperature: if the lowest temperature is 0 to -5 ℃, choose -10 diesel; if the lowest temperature is -10 to -15 ℃, choose -20 diesel; if the lowest temperature is not lower than -30 ℃, choose -35 diesel; if the lowest temperature is about -40 ℃, choose -50 diesel. Therefore, when choosing diesel oil, the freezing point should be 5~10 ℃ lower than the local temperature. The engine oil used in winter has a high viscosity, which brings difficulties to lubrication and starting, so it should be replaced with No. 8 diesel engine oil; the lubricating oil in the gearbox and rear axle should be replaced with No. 11 diesel engine oil or No. 20 gear oil.

driving habits are strictly prohibited:

do not pay attention to driving methods, illegal operation. For example, before the engine is turned off, the throttle is blown indiscriminately, thinking that some diesel can be stored in the cylinder to facilitate easy starting next time. In fact, doing so will only cause the diesel to not be completely burned in the cylinder and cause carbon deposits, and may flow into the oil pan along the cylinder wall to dilute the oil, which will not only be of no benefit to the next start, but also affect the lubrication performance of the oil. Others do not add diesel in time, and fill the tractor fuel tank with diesel before the winter flameout. Otherwise, the water vapor in the air in the empty tank will be liquefied and condensed into water droplets after being cooled by the tank wall, which will be mixed into the diesel oil, causing the engine to fail to work normally.

2. Plant Protection UAV

plant protection unmanned aerial vehicles and related ancillary products operate in fields with complex environment. External factors such as dust, liquid medicine, dew and sundries affect the performance of the products. Timely clean and maintain the equipment, clean and wipe, lubricate and apply oil, check and calibrate, replace wearing parts, etc. to ensure that the equipment is in the best condition and prolong the service life of the products.

cleaning appearance: the operating environment of flying anti-plant protection is complex, and a large amount of liquid medicine and dust will adhere to the appearance of the equipment. timely cleaning will prevent corrosion of components from affecting normal operation.

structure inspection: The machine body of the plant protection drone has strong vibration. Check the bolts, buckles, rivets and other connecting parts. If there is wear, damage, looseness, slippage, rust, etc., replace or apply oil in time.

wearing parts: pesticides are corrosive to varying degrees, and parts in contact with pesticides (pipes, adapters, nozzles, flow meters, level gauges, etc.) should be checked and replaced in time.

battery maintenance:

Do not charge and discharge in high/low temperature environment. Extreme temperatures will affect the performance and life of the battery. Before charging, check whether the used battery has been cooled. Do not charge and discharge in a cold garage, basement, direct sunlight or near a heat source.

Batteries should be stored in a cool environment. Long-term storage of the battery, can be placed in a sealed bag or sealed explosion-proof box is better, the recommended ambient temperature of 10 ~ 25C, and dry, non-corrosive gas.

plant protection UAV should keep the battery warm before taking off, and keep the battery in a warm environment, such as in the house, in the car, in the incubator, etc. To quickly install the battery when taking off and perform the flight mission. When flying at low temperatures, try to shorten the time to half of the normal temperature state to ensure safe flight.

The normal use and maintenance of the battery of the land plant protection drone is an important way to extend the service life of the drone. Therefore, when maintaining the battery, it is necessary to pay attention to the above matters to ensure that the battery of the plant protection drone is not damaged and can be used normally.

3. Combine harvester

The sundries at the connection of the harvester should be cleaned, lubricated or sealed with oil injection; if the paint peeling of the rust-prone parts leads to exposure, it is necessary to paint in time to prevent rust. If it is a rubber belt, it should be wiped and dried to prevent pests and mice from harming. The metal chain can be cleaned with kerosene or diesel oil, then soaked in engine oil for 15-40 minutes, or soaked overnight, taken out and aired until no oil drips, coated with softening oil, and then wrapped in kraft paper and placed in a dry and ventilated place to avoid mildew and deformation.

harvester. They are easily aged and deteriorated after being exposed to sunlight, and their elasticity is poor, which will affect their use in the coming year. In the storage of these products, with paraffin oil coated on the surface, and then placed in direct sunlight in a ventilated dry place. Plastic products and springs will be deformed due to long-term pressure or improper storage, so the spring should be relaxed, the conveyor belt and the like should be disassembled and stored separately.

In addition, some random utensils, especially special tools and various spare parts, need to be stored separately and put in place after use to avoid loss caused by misplacing.

4. Baler

After each use of the baler, it must be maintained, cleaned and maintained, otherwise it is likely to affect its life. After the baler and the power machine are equipped, drive to the harvested wheat field, check whether the power of the power machine is in good contact with the baler, then start, pick up, and bundle. After hearing the alarm, stop the car and increase the throttle to make the baler fast. After hearing the sound of the rope being cut, pull the rope slightly and lift the back cover of the baler to make the grass baler drop, the next grass picking can be carried out after the bale is discharged, so that the cycle continues until the work is completed, and then after use, it should be cleaned to clean up all impurities such as straw in the machine, otherwise it will malfunction after a long time, affecting normal use.

cleaning: The baler should be cleaned with high-pressure gas, and protective glasses should be worn during cleaning to avoid damage to the glasses. Secondly, it can also be cleaned by the high-speed and large-capacity wind generated by the fan. Remember not to clean the baler with water, because the residue left after cleaning will cause the body to rust when soaked in water.

lubrication: baler need to lubricate the place generally includes roller chain and wheel bearing two parts. Generally speaking, every 1000 bales need to be lubricated with oil to all chains, but it is easy to absorb dust, so you can choose to lubricate the chain regularly at the end of the season and during the idle period, so that the chain is not as easy to be contaminated as it is during operation. The wheel bearings need to be removed for cleaning and replacement every year. When lubricating the wheel bearings, the bearing adjustment bolts should be tightened, and the wheel should be rotated at the same time, and the rotation will stop when it encounters resistance.